Skylight Installation & Repair · Austin, TX

Metal Roof Skylight Installation & Repair in Austin

A skylight on a metal roof is only as good as its flashing. We install skylights on standing seam and exposed-fastener roofs with curbs flashed in metal formed to your panel profile, and we fix leaking skylights by rebuilding the flashing that's actually failing.

● Metal roofing in Austin since 2002● Standing seam & exposed fastener● 2204 W Anderson Ln

Why Skylights on Metal Roofs Leak

Most skylight leaks on metal roofs have nothing to do with the glass. They come from the flashing around the curb. A metal roof moves as it heats and cools through an Austin day, and it carries a lot of water down each panel in a hard rain. A skylight sits right in that water path. If the flashing wasn't formed to the panel profile, if it depends on sealant alone, or if nothing turns the water around the uphill side of the curb, the leak is a matter of time.

Sealant instead of flashing

Caulk and tape cure, crack and pull away in Texas sun. Sealant should back up metal flashing, not replace it.

Flashing not formed to the panels

Flat flashing laid over ribbed panels leaves gaps at every rib. Water finds them in the first wind-driven rain.

No diverter above the curb

Without a diverter or cricket on the uphill side, the full flow of the panels runs straight into the back of the curb.

Curb cut through a seam

A skylight opening that cuts a standing seam without a proper curb breaks the roof's main waterproofing line.

Skylight Installation on Metal Roofs

We install skylights during a new metal roof or add them to an existing one. Either way, the work and the flashing are written into the scope before we start, so you know exactly how the opening will be built.

  1. Plan the location

    We place the skylight to work with the panel layout, ideally between seams on a standing seam roof, and check the framing below so the opening doesn't cut a rafter that's carrying load.

  2. Frame the opening

    The roof opening is cut and framed with headers so the structure stays sound, and the opening is sized to the skylight maker's specifications.

  3. Build the curb

    A raised curb lifts the skylight above the water running down the panels, so the glass and its seal never sit in a stream of water.

  4. Flash in metal formed to the panel

    Flashing is formed to your panel profile, with closures where the panels' ribs meet the flashing, so there are no gaps for wind-driven rain.

  5. Add a diverter upslope

    A diverter above the curb sends water around both sides of the skylight instead of into its back edge.

  6. Finish to match

    Trim and flashing are finished to match the roof, and the interior shaft is finished so the skylight looks like it was always there.

Skylight Repair on Metal Roofs

When a skylight leaks, we start on the roof, not under the stain. We check the curb flashing, the diverter, the closures and the sealant, then the skylight unit itself. Most of the time the fix is reflashing the curb properly in metal to match the roof. When the skylight unit itself has failed, such as cracked glazing, a failed seal or a fogged insulated unit, we replace it and flash the new one correctly at the same time.

  • Reflashing: old flashing removed and new flashing formed to the panel profile, with a diverter added if one is missing.
  • Curb repair: rotted or short curbs rebuilt so the skylight sits high enough above the water line.
  • Unit replacement: cracked, leaking or fogged skylights replaced with a properly sized unit.
  • Removal: if you'd rather not keep a problem skylight, we can close the opening and patch the roof with matching panels.

A skylight leak can look like a roof leak, and a roof leak can look like a skylight leak. Our metal roof repair process traces water at the roof so we fix the right thing. If water is coming in right now, call for emergency metal roof repair.

Skylights by Metal Roof Type

Standing seam

Skylights placed to work with the seam layout, with curb flashing that ties into the seams so the roof keeps its concealed-fastener design.

Exposed fastener

Corrugated and R-panel roofs need closures matched to the rib profile and fastener placement that keeps screws out of the water path.

Stone-coated steel

Flashing kits and trim matched to the shake, tile or shingle profile of the panels.

Planning a new roof? Adding a skylight during a metal roof installation or metal roof replacement is simpler than adding one later, because the flashing goes in with the panels.

Metal Roof Skylight FAQs

Can you add a skylight to an existing metal roof?

Yes. We frame the opening, build a curb and flash it in metal formed to your panel profile, with a diverter above the curb. The work and flashing details are written into the scope before we start.

Why is my skylight leaking on my metal roof?

Most skylight leaks on metal roofs are at the flashing, not the glass: failed sealant, flashing that was never formed to the panel, or a missing diverter above the curb. We check those first.

Do you replace the skylight or just reflash it?

It depends on what failed. If the unit is sound, reflashing the curb usually fixes the leak. If the glazing is cracked, the seal has failed or an insulated unit has fogged, we replace the unit and reflash it.

Do skylights work with standing seam metal roofs?

Yes. They're best placed between seams, with curb flashing that ties into the seams so the roof keeps its concealed-fastener design.

Should I add a skylight when I get a new metal roof?

If you want one, a new roof is the best time. The opening is framed and flashed as the panels go on, instead of cutting into a finished roof later.

Can you remove a skylight I don't want anymore?

Yes. We close and frame the opening, deck it, and patch the roof with matching panels and trim.

Leaking Skylight or Planning a New One?

Call us or request an estimate. We'll look at the roof, the curb and the flashing and tell you exactly what it needs.